![]() Interface flags: SNMP-Traps Internal: 0x4000ĬoS queues : 8 supported, 4 maximum usable queuesĬurrent address: 00:1f:12:fe:c5:2e, Hardware address: 00:1f:12:fe:c5:2e MAC-REWRITE Error: None, Loopback: Enabled, Source filtering: Disabled,įlow control: Enabled, Auto-negotiation: Enabled, Remote fault: Onlineĭevice flags : Present Running Loop-Detected Link-level type: Ethernet, MTU: 1514, Speed: 1000mbps, BPDU Error: None, Sample Output show interfaces ge-4/0/6 extensive Physical interface: ge-4/0/6, Enabled, Physical link is Up Interface index: 144, SNMP ifIndex: 516, Generation: 147 Interface (CLI) operational mode command: show interfaces ( fe- fpc/ port | ge- fpc/ pic/ port) To verify that the status of the Fast Ethernet or GigabitĮthernet interface is up, use the following Junos OS command-line | gigether-options] hierarchy level, places the interface into Interfaces interface-name (fastether-options Simply including the loopback statement at the [edit There is no option to use a local or remote statement. On anĮthernet interface, you cannot create a remote loopback, therefore Of the PIC but does not test the transmit and receive ports. A local loopback tests the interconnection When you create a local loopback, you create an internal loop In configuration mode, go to the following hierarchy level: edit interfaces interface-name (fastether-options | gigether-options)Ĭonfigure the local loopback: [edit interfaces interface-name (fastether-options | set loopbackįor example: [edit interfaces fe-1/0/0 showįor example: [edit interfaces fe-1/0/0 commit The transmit port to the receive port, follow these steps: To configure a local loopback without physically connecting Perform Steps 2 through 8 from Diagnose a Suspected Hardware Problem with a Fast Show interfaces (fe- fpc/pic/port | ge- fpc/pic/port ) extensive Interface (fe- fpc/pic/port | ge- fpc/pic/port count 100 rapidĬheck for Fast Ethernet or Gigabit Ethernet Interface Ping the Fast Ethernet or Gigabit Ethernet Interface Interface-name unit logical-unit-number family inet addressĬlear Fast Ethernet or Gigabit Ethernet InterfaceĬlear interfaces statistics fe- fpc/pic/port | ge- fpc/pic/port ![]() Show interfaces ge- fpc/pic/port [edit interfaces Show interfaces (fe- fpc/pic/port | ge- fpc/pic/port)Ĭonfigure a Static Address Resolution Protocol Table Verify That the Fast Ethernet or Gigabit Ethernet Interface-name (fastether-options | gigether-options)] You can now close out of any open windows you have.For Using Loopback Testing for Fast Ethernet and Gigabit Ethernetĭiagnose a Suspected Hardware Problem with a FastĬreate a Physical Loopback for a Fiber-Optic InterfaceĬonnect the transmit port to the receive port.Ĭreate a Loopback Plug for an RJ-45 Ethernet InterfaceĬross pin 1 (TX+) and pin 3 (RX+) together, and pin 2 In the IP Settings tab, uncheck "Automatic metric" and then enter 1 for the Interface metric.ĩ. On the General tab, select the "Advanced" button at the bottom.ħ. Highlight Internet Protocol Version 4 (TCP/IPv4) and select "Properties."Ħ. Find the Loopback Adapter we installed, right-click and select "Properties."ĥ. In the Network and Sharing Center, select "Change adapter settings" from the left-hand side.Ĥ. In the Control Panel, select Network and Sharing Centerģ. Right click on the Windows icon and search for "Control Panel."Ģ. ![]() To adjust the metrics, follow these steps:ġ. How to ensure data is always passed through the network adapterīy adjusting the metrics for the network adapter, we can ensure data is always passed through it first. Once the Loopback adapter is installed, we will have a virtual "always on" connection, so even if the physical network connection is lost, the virtual adapter will remain active. Select the Microsoft KM-TEST Loopback Adapter card model. Then click "Next." Scroll down and select Network Adapters from the common hardware types listed.Ħ. Choose "Install the Hardware that I manually select from a list" and then click "Next."ĥ. Click on the Action menu at the top of the window and select "Add Legacy Hardware."Ĥ. Right click on the Windows Start menu icon and select Device Manager.Ģ. To install a Loopback adapter for Windows 10 please follow these steps:ġ. The loopback adapter will help to maintain a local "virtual" network connection, which is needed for Retail Pro Prism to run. How to Install a Loopback Adapter for Retail Pro PrismĪ Loopback adapter can be used to help maintain network stability when a host machine is having network connection issues with either a physical connection or virtual VPN connection. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |